top of page
Search

What is my Party Wall made of?

TPWP
Nov 2
6 min read
A Construction project inside an old house showing the structure made of different materials

The quick answer: it depends mostly on when your house was built. Older terraces and semis usually share a solid brick wall. Newer homes tend to have two separate layers of blockwork with a gap in between. Knowing which you have makes a real difference to how a loft conversion, chimney breast removal or extension is planned, and to what your neighbour needs to be told.


Something to keep in mind before you read on: this is a rule of thumb, not a guarantee. Builders in the past varied a lot from street to street, and many houses have been altered alot since they were built. The only way to be certain is to actually open up the wall and look inside the structure, you or your builder can do this by opening up a small inspection hole. Your designer or structural engineer should confirm what's there before the work is designed.


The short version

When it was built

Party wall in the main house

Party wall in the loft

Before 1919 (Victorian and Edwardian)

Solid 9-inch brick in lime mortar

Often 9-inch brick, but can be half-brick, or missing altogether in cheaper terraces

1919 to 1939 (interwar)

Solid 9-inch brick

Often half-brick or clinker block

1945 to 1965 (post-war)

Solid brick or dense concrete block. Concrete in some non-traditional houses

Clinker or breeze block is common

1965 to 1985

Solid masonry about 215 mm thick, or a cavity wall of two 100 mm leaves with a 50 mm gap

Usually carried up to the roof as a fire break

1985 to 2003

Cavity wall: two leaves of block with a gap between

Carried up to the underside of the roof and fire-stopped

2003 to today

Cavity block with a wider gap, often filled with mineral wool, or twin timber-frame walls

Fire-stopped, with cavity barriers at the eaves


Solid brick: the 9-inch wall

Up until around the 1960s, most party walls between terraced and semi-detached houses were solid "one brick" walls, about 9 inches (215 to 230 mm) thick. It's a separating wall sitting on the 'boundary' and shared by both houses. Older walls are laid in soft lime mortar.

Half-brick walls, about 4½ inches thick, turn up in the loft spaces of older terraces, in rear outriggers and back additions, and in some cheaply built Victorian housing. Some early terraces have no party wall in the roof space at all. That matters for fire separation, and it's one of the first things to check on a loft conversion. Adding a party wall in your loft is notifiable work under the Act.


When did cavity walls arrive?

Cavity walls started appearing on external walls in the 1920s, usually with a 2-inch (50 mm) gap. Party walls mostly stayed solid until the 1965 Building Regulations brought in national sound-insulation standards. Those allowed either a heavy solid wall or two separate leaves with a gap, and the cavity version became the norm on new estates through the 1970s and 1980s.


Since the sound-insulation changes of 2003, party wall cavities have generally become wider and are often insulated. External wall cavities have widened too, thanks to energy-efficiency rules.


From brick to block

The materials changed over the decades, and you can often date a wall by what it's made from:

  • Breeze or clinker blocks (made from cinders and furnace ash) were used from the 1920s and 30s for partitions, loft-level party walls and inner leaves. They can be crumbly and poor when it comes to carrying loads.

  • Dense concrete blocks took over from the 1950s and 60s, as post-war brick shortages pushed builders towards block.

  • Lightweight aircrete blocks became standard for inner leaves from the 1960s and 70s. They're less common as the main party wall layer, because they're too light for good sound insulation unless a higher-density grade is used.

  • Metric bricks replaced imperial sizes around 1970. So a "9-inch" wall built after that is really 215 mm.


Post-war "non-traditional" houses

Brick and labour shortages after the Second World War led to new building systems, used mainly on council estates from the late 1940s to the 1970s. There are two you're most likely to meet:

No-fines concrete houses have walls of concrete poured on site, made from cement and coarse stones with no sand. That leaves small air pockets throughout, a bit like a honeycomb. The walls are usually 200 to 300 mm thick and rendered or pebble-dashed outside. The party wall is normally the same concrete. In the loft it looks like grey, lumpy concrete with visible stones and no mortar joints.

Precast reinforced concrete (PRC) houses, such as Airey and Cornish, are built from factory-made concrete posts and panels. Many PRC types were officially designated defective in the 1980s because their steel reinforcement can corrode, and some have since been repaired under approved schemes. No-fines houses weren't designated defective and are generally regarded as sound.

Either way, cutting into voided or precast concrete for beams, chases or fixings behaves very differently from brickwork. A structural engineer needs to design for it specifically, sometimes after taking a core sample. Noise and vibration also travel further through the structure.


Why it matters for your building work

Steel beams for loft conversions. In a solid 9-inch wall, beam pockets can only go in so far, generally to about the middle of the wall, with padstones beneath. That's work to a shared structure. In a cavity party wall the work normally goes into your own leaf only, but it's still a party structure, so a notice is still required. Loft-level walls of half-brick or clinker block may need rebuilding or strengthening before they can carry beams, and that should be covered in the notice and the award.

Chimney breast removal. In houses built before the 1960s, chimney breasts usually sit back to back on the party wall, with shared stacks above. Removing them needs a notice, proper support for whatever sits above, and a careful record of the condition of the house next door. Gallows brackets are not usually approved by Building Control and can't be used when next door have removed their chimney breast already.

Extensions and foundations. Victorian and interwar houses have shallow, stepped footings. A modern extension foundation close to the boundary will very often go deeper than the neighbour's, which can bring an adjacent excavation notice into play. Typically that applies within 3 metres of the neighbouring building, and sometimes up to 6 metres.

Existing defects. Interwar and early post-war cavity walls often suffer from wall tie corrosion, which shows up as horizontal cracking along the mortar joints. Recording it in a Schedule of Condition before work starts gives everyone a clear picture of what was already there.

Noise and vibration. Cutting into a solid 9-inch wall sends far more noise and vibration next door than working on one leaf of a cavity wall. It's worth talking your neighbours through that before work begins.


What to expect in Essex


  • Victorian and Edwardian terraces in towns such as Chelmsford, Colchester and Southend: usually solid 9-inch party walls, with half-brick or missing separation in the loft.

  • Interwar semis in the suburbs: solid brick party walls, often with clinker block or half-brick above, and 50 mm cavity external walls.

  • Post-war council estates and new-town housing, such as in Harlow and Basildon: keep an eye out for non-traditional construction, where the party wall may be concrete and needs a different approach.

  • Newer estates from the 1980s onwards: twin-leaf block cavity party walls, which are usually the simplest to work with.


Quick questions

How can I tell if my party wall is solid or cavity? The age of the house is the best first clue: before about 1965 it's almost certainly solid. In the loft you can often see the wall directly. A solid wall shows bricks laid across its full width, while a cavity wall has two separate layers with a gap. A surveyor can confirm it with a small inspection opening (if needed).

Do I still need a party wall notice if it's a cavity wall? Yes. A cavity wall separating two houses is still a party wall under the Party Wall etc. Act 1996, even if your work only touches your own leaf. Cutting into it, inserting beams or removing chimney breasts are all notifiable. Free Party Wall Checker.

What are no-fines and Airey houses? Both are post-war "non-traditional" houses, built mainly on council estates from the late 1940s to the 1970s. No-fines houses are poured concrete with no sand in the mix, usually rendered outside. Airey and Cornish houses are made from precast concrete panels and posts. Both need a structural engineer's input before anyone cuts into the party wall.

What is a breeze block? Strictly, a block made from "breeze": cinders and ash left over from coke and coal. They were widely used from the 1920s to the 1950s, and today the term is often used loosely for any concrete block. Old clinker blocks can be weak and crumbly, so they need care before being asked to carry new loads.


Not sure what you've got?

We're experienced at looking at a wall and working out what's inside it. If you're planning a loft conversion, extension or chimney breast removal in Essex or the South East, try our Free Party Wall Checker to see whether your work could be notifiable, or contact us and we'll talk it through.


 
 
 

Comments


bottom of page